SDS page gel - Revision history

Alex at 20:58, 3 February 2010

2010-02-03T20:58:34Z

← Older revision		Revision as of 20:58, 3 February 2010
Line 40:		Line 40:
	#*Carefully place gel into plastic gel box filled with water.		#*Carefully place gel into plastic gel box filled with water.

	An example of a SDS-PAGE gel run with two protein samples is shown here. Lane#1: Marker, Lane#2: MrR70A-NC5, Lane#3: HR3102A-NC5.~~<br> [~~[~~Image~~:~~Nupage gel~~.~~gif]~~]		[[Image:Nupage gel.gif\|left]]
			An example of a SDS-PAGE gel run with two protein samples is shown here. Lane#1: Marker, Lane#2: MrR70A-NC5, Lane#3: HR3102A-NC5.

			The marker used is [http://www.bio-rad.com Bio-Rad] catalog #161-6374 with molecular weights 10, 15, 20, 25, 37, 50, 75, 100, 150, 250 kDa from bottom to top.

Bs59 at 21:58, 10 December 2009

2009-12-10T21:58:55Z

← Older revision		Revision as of 21:58, 10 December 2009
Line 21:		Line 21:
	#Fill the buffer core with 200 mL 1X RB. Make sure this section does NOT leak before adding liquid to the outside. Carefully remove the comb and pipette out any air bubbles. Then, fill outer part of case with 600 mL of RB.<br>		#Fill the buffer core with 200 mL 1X RB. Make sure this section does NOT leak before adding liquid to the outside. Carefully remove the comb and pipette out any air bubbles. Then, fill outer part of case with 600 mL of RB.<br>
	#Fill the wells with samples:<br>		#Fill the wells with samples:<br>
	#*Add 10 μL MW markers to 1 ~~well~~<br>		#*Add 10 μL MW markers to well #1.<br>
	#*Fill remaining 11 wells with 10 μL of prepared protein sample solution.		#*Fill remaining 11 wells with 10 μL of prepared protein sample solution.
	#*Fill each well slowly. Try to avoid bubbles in wells that may cause overflow into other wells<br>		#*Fill each well slowly. Try to avoid bubbles in wells that may cause overflow into other wells<br>
Line 40:		Line 40:
	#*Carefully place gel into plastic gel box filled with water.		#*Carefully place gel into plastic gel box filled with water.

	<br> [[Image:Nupage gel.gif]]		An example of a SDS-PAGE gel run with two protein samples is shown here. Lane#1: Marker, Lane#2: MrR70A-NC5, Lane#3: HR3102A-NC5.<br> [[Image:Nupage gel.gif]]

TheresaRamelot at 14:28, 7 December 2009

2009-12-07T14:28:22Z

← Older revision		Revision as of 14:28, 7 December 2009
Line 11:		Line 11:
	==== I. Sample Preparation ====		==== I. Sample Preparation ====

	#Add 5 μL 4X Reducing Buffer to 15μL protein solution. Vortex sample to mix.		#Add 5 μL 4X Reducing Buffer (RB) to 15μL protein solution. Vortex sample to mix.
	#Heat samples at 70 °C for 10 mins.		#Heat samples at 70 °C for 10 mins.
	#Spin samples.		#Spin samples.



	==== II. NuPage Gels ====		==== II. NuPage Gels ====

TheresaRamelot at 23:03, 3 December 2009

2009-12-03T23:03:20Z

← Older revision		Revision as of 23:03, 3 December 2009
Line 42:		Line 42:
	#*Carefully place gel into plastic gel box filled with water.		#*Carefully place gel into plastic gel box filled with water.

	<br>		<br> [[Image:Nupage gel.gif]]
	[[~~image~~:~~nupage_gel~~]]

TheresaRamelot at 23:03, 3 December 2009

2009-12-03T23:03:03Z

← Older revision		Revision as of 23:03, 3 December 2009
Line 30:		Line 30:
	#*Turn on (be sure Range Select is OFF). Set Range to 200V/400mA, then hit Start.		#*Turn on (be sure Range Select is OFF). Set Range to 200V/400mA, then hit Start.
	#*Run for 35 min. When done, then turn off.<br>		#*Run for 35 min. When done, then turn off.<br>
	#Gel stain:		#Gel stain:
	#*Take gel cassette out of Invitrogen gel box.		#*Take gel cassette out of Invitrogen gel box.
	#*Fill microwave safe glass container with MilliQ water enough as to immerse gel.		#*Fill microwave safe glass container with MilliQ water enough as to immerse gel.
	#*Crack open gel cassette and place gel in microwave safe glass container.		#*Crack open gel cassette and place gel in microwave safe glass container.
Line 43:		Line 43:

	<br>		<br>
			[[image:nupage_gel]]

TheresaRamelot at 20:59, 3 December 2009

2009-12-03T20:59:00Z

← Older revision		Revision as of 20:59, 3 December 2009
Line 18:		Line 18:

	==== II. NuPage Gels ====		==== II. NuPage Gels ====



	#Remove precast gels (4-12 % Bis-Tris gels from Invitrogen) from package. Cut open and dump out liquid in sink. Wash outside with MilliQ water. Pull off white stripe at bottom.<br>		#Remove precast gels (4-12 % Bis-Tris gels from Invitrogen) from package. Cut open and dump out liquid in sink. Wash outside with MilliQ water. Pull off white stripe at bottom.<br>
Line 30:		Line 28:
	#*When working with 2 gel plates, make sure to label the outside of the container.<br>		#*When working with 2 gel plates, make sure to label the outside of the container.<br>
	#Match the + and -electrode ends (same colors)		#Match the + and -electrode ends (same colors)
	#*Turn on (be sure Range Select is OFF). Set Range to 200V/400mA, then hit Start.		#*Turn on (be sure Range Select is OFF). Set Range to 200V/400mA, then hit Start.
	#*Run for 35 min. When done, then turn off.<br>		#*Run for 35 min. When done, then turn off.<br>
	#Gel stain:		#Gel stain:
			#*Take gel cassette out of Invitrogen gel box.
	#*Take gel cassette out of Invitrogen gel box.
	#*Fill microwave safe glass container with MilliQ water enough as to immerse gel.		#*Fill microwave safe glass container with MilliQ water enough as to immerse gel.
	#*Crack open gel cassette and place gel in microwave safe glass container.		#*Crack open gel cassette and place gel in microwave safe glass container.

TheresaRamelot at 20:57, 3 December 2009

2009-12-03T20:57:39Z

← Older revision		Revision as of 20:57, 3 December 2009
Line 19:		Line 19:
	==== II. NuPage Gels ====		==== II. NuPage Gels ====

	*

	#Remove precast gels (4-12 % Bis-Tris gels from Invitrogen) from package. Cut open and dump out liquid in sink. Wash outside with MilliQ water. Pull off white stripe at bottom.<br>
	#Lower buffer core into cell and insert gel cassettes on both sides (make sure the shorter well side faces inward). Insert tension wedge and lock in place. (*If only running one gel, be sure to place buffer dam between the core and the tension wedge).<br>		#Remove precast gels (4-12 % Bis-Tris gels from Invitrogen) from package. Cut open and dump out liquid in sink. Wash outside with MilliQ water. Pull off white stripe at bottom.<br>
	#Fill the buffer core with 200 mL 1X RB. Make sure this section does NOT leak before adding liquid to the outside. Carefully remove the comb and pipette out any air bubbles. Then, fill outer part of case with 600 mL of RB.<br>		#Lower buffer core into cell and insert gel cassettes on both sides (make sure the shorter well side faces inward). Insert tension wedge and lock in place. (*If only running one gel, be sure to place buffer dam between the core and the tension wedge).<br>
	#Fill the wells with samples:<br>		#Fill the buffer core with 200 mL 1X RB. Make sure this section does NOT leak before adding liquid to the outside. Carefully remove the comb and pipette out any air bubbles. Then, fill outer part of case with 600 mL of RB.<br>
	#Add 10 μL MW markers to 1 well<br>		#Fill the wells with samples:<br>
	#Fill remaining 11 wells with 10 μL of prepared protein sample solution. -Fill each well slowly. Try to avoid bubbles in wells that may cause overflow into other wells<br>		#*Add 10 μL MW markers to 1 well<br>
	#When working with 2 gel plates, make sure to label the outside of the container.<br>		#*Fill remaining 11 wells with 10 μL of prepared protein sample solution.
			#*Fill each well slowly. Try to avoid bubbles in wells that may cause overflow into other wells<br>
			#*When working with 2 gel plates, make sure to label the outside of the container.<br>
	#Match the + and -electrode ends (same colors)		#Match the + and -electrode ends (same colors)
	##Turn on (be sure Range Select is OFF). Set Range to 200V/400mA, then hit Start.		#*Turn on (be sure Range Select is OFF). Set Range to 200V/400mA, then hit Start.
	##Run for 35 min. When done, then turn off.<br>		#*Run for 35 min. When done, then turn off.<br>
	#Gel stain:		#Gel stain:

	**Take gel cassette out of Invitrogen gel box.		#*Take gel cassette out of Invitrogen gel box.
	**Fill microwave safe glass container with MilliQ water enough as to immerse gel.		#*Fill microwave safe glass container with MilliQ water enough as to immerse gel.
	**Crack open gel cassette and place gel in microwave safe glass container.		#*Crack open gel cassette and place gel in microwave safe glass container.
	**Microwave gel for two minutes or until water boils.		#*Microwave gel for two minutes or until water boils.
	**Place container on shaker until cool. Then decant the water. Rinse one more time with MilliQ water.		#*Place container on shaker until cool. Then decant the water. Rinse one more time with MilliQ water.
	**Add Denville Blue Protein Stain to gel container and immerse gel.		#*Add Denville Blue Protein Stain to gel container and immerse gel.
	**Microwave gel for two minutes or until protein stain solution boils and place on shaker until cool.		#*Microwave gel for two minutes or until protein stain solution boils and place on shaker until cool.
	**Decant gel stain into waste container, and rinse gel with MilliQ water.		#*Decant gel stain into waste container, and rinse gel with MilliQ water.
	**Add MilliQ water to immerse gel and microwave for two minutes and then shake until cool.		#*Add MilliQ water to immerse gel and microwave for two minutes and then shake until cool.
	**Carefully place gel into plastic gel box filled with water.		#*Carefully place gel into plastic gel box filled with water.

	<br>		<br>

TheresaRamelot at 20:55, 3 December 2009

2009-12-03T20:55:50Z

← Older revision		Revision as of 20:55, 3 December 2009
Line 19:		Line 19:
	==== II. NuPage Gels ====		==== II. NuPage Gels ====

	#Remove precast gels (4-12 % Bis-Tris gels from Invitrogen) from package. Cut open and dump out liquid in sink. Wash outside with MilliQ water. Pull off white stripe at bottom.		*
	#Lower buffer core into cell and insert gel cassettes on both sides (make sure the shorter well side faces inward). Insert tension wedge and lock in place. (*If only running one gel, be sure to place buffer dam between the core and the tension wedge).
	#Fill the buffer core with 200 mL 1X RB. Make sure this section does NOT leak before adding liquid to the outside. Carefully remove the comb and pipette out any air bubbles. Then, fill outer part of case with 600 mL of RB.		#Remove precast gels (4-12 % Bis-Tris gels from Invitrogen) from package. Cut open and dump out liquid in sink. Wash outside with MilliQ water. Pull off white stripe at bottom.<br>
	#Fill the wells with samples:		#Lower buffer core into cell and insert gel cassettes on both sides (make sure the shorter well side faces inward). Insert tension wedge and lock in place. (*If only running one gel, be sure to place buffer dam between the core and the tension wedge).<br>
	**Add 10 μL MW markers to 1 well		#Fill the buffer core with 200 mL 1X RB. Make sure this section does NOT leak before adding liquid to the outside. Carefully remove the comb and pipette out any air bubbles. Then, fill outer part of case with 600 mL of RB.<br>
	**Fill remaining 11 wells with 10 μL of prepared protein sample solution. -Fill each well slowly. Try to avoid bubbles in wells that may cause overflow into other wells		#Fill the wells with samples:<br>
	**When working with 2 gel plates, make sure to label the outside of the container.		#Add 10 μL MW markers to 1 well<br>
	#Match the + and -electrode ends (same colors) -Turn on (be sure Range Select is OFF). Set Range to 200V/400mA, then hit Start. -Run for 35 min. When done, then turn off.		#Fill remaining 11 wells with 10 μL of prepared protein sample solution. -Fill each well slowly. Try to avoid bubbles in wells that may cause overflow into other wells<br>
			#When working with 2 gel plates, make sure to label the outside of the container.<br>
			#Match the + and -electrode ends (same colors)
			##Turn on (be sure Range Select is OFF). Set Range to 200V/400mA, then hit Start.
			##Run for 35 min. When done, then turn off.<br>
	#Gel stain:		#Gel stain:

	**Take gel cassette out of Invitrogen gel box.		**Take gel cassette out of Invitrogen gel box.
	**Fill microwave safe glass container with MilliQ water enough as to immerse gel.		**Fill microwave safe glass container with MilliQ water enough as to immerse gel.
Line 38:		Line 43:
	**Add MilliQ water to immerse gel and microwave for two minutes and then shake until cool.		**Add MilliQ water to immerse gel and microwave for two minutes and then shake until cool.
	**Carefully place gel into plastic gel box filled with water.		**Carefully place gel into plastic gel box filled with water.

			<br>

TheresaRamelot at 20:53, 3 December 2009

2009-12-03T20:53:07Z

TheresaRamelot at 20:52, 3 December 2009

2009-12-03T20:52:28Z

← Older revision		Revision as of 20:52, 3 December 2009
Line 22:		Line 22:
	#Lower buffer core into cell and insert gel cassettes on both sides (make sure the shorter well side faces inward). Insert tension wedge and lock in place. (*If only running one gel, be sure to place buffer dam between the core and the tension wedge).		#Lower buffer core into cell and insert gel cassettes on both sides (make sure the shorter well side faces inward). Insert tension wedge and lock in place. (*If only running one gel, be sure to place buffer dam between the core and the tension wedge).
	#Fill the buffer core with 200 mL 1X RB. Make sure this section does NOT leak before adding liquid to the outside. Carefully remove the comb and pipette out any air bubbles. Then, fill outer part of case with 600 mL of RB.		#Fill the buffer core with 200 mL 1X RB. Make sure this section does NOT leak before adding liquid to the outside. Carefully remove the comb and pipette out any air bubbles. Then, fill outer part of case with 600 mL of RB.
	#Fill the wells with samples:		#Fill the wells with samples:

	*Add 10 μL MW markers to 1 well		*Add 10 μL MW markers to 1 well
	*Fill remaining 11 wells with 10 μL of prepared protein sample solution. -Fill each well slowly. Try to avoid bubbles in wells that may cause overflow into other wells		*Fill remaining 11 wells with 10 μL of prepared protein sample solution. -Fill each well slowly. Try to avoid bubbles in wells that may cause overflow into other wells
	*When working with 2 gel plates, make sure to label the outside of the container.		*When working with 2 gel plates, make sure to label the outside of the container.

	#Match the + and -electrode ends (same colors) -Turn on (be sure Range Select is OFF). Set Range to 200V/400mA, then hit Start. -Run for 35 min. When done, then turn off.		#Match the + and -electrode ends (same colors) -Turn on (be sure Range Select is OFF). Set Range to 200V/400mA, then hit Start. -Run for 35 min. When done, then turn off.
	#Gel stain:		#Gel stain:

	*Take gel cassette out of Invitrogen gel box.		*Take gel cassette out of Invitrogen gel box.
	*Fill microwave safe glass container with MilliQ water enough as to immerse gel.		*Fill microwave safe glass container with MilliQ water enough as to immerse gel.

← Older revision		Revision as of 20:53, 3 December 2009
Line 23:		Line 23:
	#Fill the buffer core with 200 mL 1X RB. Make sure this section does NOT leak before adding liquid to the outside. Carefully remove the comb and pipette out any air bubbles. Then, fill outer part of case with 600 mL of RB.		#Fill the buffer core with 200 mL 1X RB. Make sure this section does NOT leak before adding liquid to the outside. Carefully remove the comb and pipette out any air bubbles. Then, fill outer part of case with 600 mL of RB.
	#Fill the wells with samples:		#Fill the wells with samples:
	*Add 10 μL MW markers to 1 well		**Add 10 μL MW markers to 1 well
	*Fill remaining 11 wells with 10 μL of prepared protein sample solution. -Fill each well slowly. Try to avoid bubbles in wells that may cause overflow into other wells		**Fill remaining 11 wells with 10 μL of prepared protein sample solution. -Fill each well slowly. Try to avoid bubbles in wells that may cause overflow into other wells
	*When working with 2 gel plates, make sure to label the outside of the container.		**When working with 2 gel plates, make sure to label the outside of the container.
	#Match the + and -electrode ends (same colors) -Turn on (be sure Range Select is OFF). Set Range to 200V/400mA, then hit Start. -Run for 35 min. When done, then turn off.		#Match the + and -electrode ends (same colors) -Turn on (be sure Range Select is OFF). Set Range to 200V/400mA, then hit Start. -Run for 35 min. When done, then turn off.
	#Gel stain:		#Gel stain:
	*Take gel cassette out of Invitrogen gel box.		**Take gel cassette out of Invitrogen gel box.
	*Fill microwave safe glass container with MilliQ water enough as to immerse gel.		**Fill microwave safe glass container with MilliQ water enough as to immerse gel.
	*Crack open gel cassette and place gel in microwave safe glass container.		**Crack open gel cassette and place gel in microwave safe glass container.
	*Microwave gel for two minutes or until water boils.		**Microwave gel for two minutes or until water boils.
	*Place container on shaker until cool. Then decant the water. Rinse one more time with MilliQ water.		**Place container on shaker until cool. Then decant the water. Rinse one more time with MilliQ water.
	*Add Denville Blue Protein Stain to gel container and immerse gel.		**Add Denville Blue Protein Stain to gel container and immerse gel.
	*Microwave gel for two minutes or until protein stain solution boils and place on shaker until cool.		**Microwave gel for two minutes or until protein stain solution boils and place on shaker until cool.
	*Decant gel stain into waste container, and rinse gel with MilliQ water.		**Decant gel stain into waste container, and rinse gel with MilliQ water.
	*Add MilliQ water to immerse gel and microwave for two minutes and then shake until cool.		**Add MilliQ water to immerse gel and microwave for two minutes and then shake until cool.
	*Carefully place gel into plastic gel box filled with water.		**Carefully place gel into plastic gel box filled with water.