Resonance Assignment/Abacus/Spin systems identification: Difference between revisions

From NESG Wiki
Jump to navigation Jump to search
No edit summary
No edit summary
 
(42 intermediate revisions by 2 users not shown)
Line 1: Line 1:
<div>Normally, the NMR spectra shown in [[Introduction to ABACUS#NMR_spectra_required_for_ABACUS|Table 1]] are collected for ABCUS. Spectra should ideally be collected from the same protein preparation and under the same conditions to make sure peaks are within tolerance between spectra. All spectra need to be appropriately synchronized <span>and calibrated against reference spectra of your choice. It is a good idea to use as a reference for spectra calibration the 2D HN-projection of 15N-NOESY and the 2D CH-projection of the 13C-NOESY. </span></div><div>&nbsp;</div>
<div>Normally, the NMR spectra shown in [[Introduction to ABACUS#NMR_spectra_required_for_ABACUS|Table 1]] are collected for ABCUS. Spectra should ideally be collected from the same protein preparation and under the same conditions to make sure peaks are within tolerance between spectra. All spectra need to be appropriately synchronized <span>and calibrated against reference spectra of your choice. It is a good idea to use as a reference for spectra calibration the 2D HN-projection of 15N-NOESY and the 2D CH-projection of the 13C-NOESY. </span></div><div>&nbsp;</div>  
== Step 1. Generate HN-rooted spin-systems (''b''PB-fragments)  ==
== Step 1. Generate HN-rooted spin-systems (''b''PB-fragments)  ==
<div>&nbsp;</div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 1.1&nbsp; </span>[[FMCGUI objects#bPB_fragment|''b''PB-fragments]]<span> can be identified using the following spectra </span></div><div><br><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 15N_HSQC</span></div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; HNCO</span></div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; CBCA(CO)NH</span></div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; HBHAC (CO)NH</span></div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; HNCA</span></div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 15N_NOESY</span></div><div>&nbsp;It is a good idea to analyze all these spectra simultaneously, for example, &nbsp;using SPARKY,&nbsp;in order to obtain &nbsp;peak lists of 15N_HSQC, HNCA, &nbsp;and CBCA(CO)HN spectra (see Figure 4.1A). The first two spectra should be referenced.</div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></div><div>&nbsp;</div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 1.2. Create initial HN-rooted spin-systems (</span><span />[[FMCGUI objects#bPB_fragment|''b''PB-fragments]]<span> </span><span>) using FMCGUI:</span></div><div>&nbsp;</div>
*<span><span>&nbsp;&nbsp; &nbsp; &nbsp; </span></span>start new project PRJ_1 {<span> Poject&gt;new </span>}
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load protein sequence {<span> DATA&gt;Protein Sequence&gt;load</span> }
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;referenced HNCA peak list { <span>DATA&gt;HNCA&gt;load</span> }<br>
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;referenced CBCA(CO)NH peak list { <span>DATA&gt;CBCACONH&gt;load</span> }<br>
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;referenced HBHA(CO)NH peak list { <span>DATA&gt;HBHACONH&gt;load </span>}
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;referenced 15N_HSQC peak list { <span>DATA&gt;N15 HSQC&gt;load</span> }<br>
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>set tolerances for matching of resonances in different spectral dimensions { <span>DATA&gt;Tolerances</span> }<br>
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>create bPB-fragments { <span>Fragment&gt;create&gt;fawn</span> }<br>
<div>First, a referenced C13_hsqc peak list is created and shown in new window ‘fake C13 HSQC’. Warning messages are shown in the project main window. You have to check the list and modify it if needed. Then, press ‘OK’ button in the ‘‘fake C13 HSQC’ window. In the result, new window ‘Create Fragment’ pops up. The window consists of three sections. The left sections contains suggested ''b''PB-fragments, while the other sections contains two reports of fragments scoring with&nbsp;both C and H resonances and with only C&nbsp;resonances, respectively. Consider warning messages shown in the project main window and check/modify generated ''b''PB-fragments in the left section of “Create Fragment” window. When satisfied, the ''b''PB-fragments will be loaded in the memory by&nbsp;clicking on “OK” button.</div>
*<span>&nbsp;&nbsp; &nbsp; &nbsp; save project PRJ_1. { Project&gt;Save } or&nbsp; { Project&gt;Quit }
</span>


1.1[[Introduction to ABACUS#bPB_fragment|''b''PB-fragments]] can be identified using the following spectra
<div><br><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 15N_HSQC</span></div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; HNCO</span></div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; CBCA(CO)NH</span></div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; HBHAC (CO)NH</span></div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; HNCA</span></div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 15N_NOESY</span></div><div>&nbsp;It is a good idea to analyze all these spectra simultaneously, for example, &nbsp;using SPARKY,&nbsp;in order to obtain &nbsp;peak lists of 15N_HSQC, HNCA,&nbsp; CBCA(CO)NH, and HBHA(CO)NH spectra (see Figure 4.1A). The first two spectra should be referenced.</div><div><span>&nbsp;</span></div><div>'''<span>&nbsp;Figure 4.1A</span>'''<span>[[Image:Fmcgui Fig4.1a.jpg|thumb|center|600px]]&nbsp; </span></div><div></div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 1.2. Create initial HN-rooted spin-systems (</span>[[Introduction to ABACUS#bPB_fragment|''b''PB-fragments]]<span> </span><span>) using FMCGUI:</span></div><div>&nbsp;</div>
*<span><span>&nbsp;&nbsp; &nbsp; &nbsp; </span></span>start new project PRJ_1 { [[FMCGUI commands#Project.3ENew|Poject&gt;new]] }
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load protein sequence { [[FMCGUI commands#Data.3EProtein_Sequence.3ELoad|DATA&gt;Protein Sequence&gt;load]] }
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;referenced HNCA peak list { [[FMCGUI commands#Data.3EHNCA.3E|DATA&gt;HNCA&gt;load]] }<br>
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;referenced CBCA(CO)NH peak list { [[FMCGUI commands#Data.3ECBCACONHN.3E|DATA&gt;CBCACONH&gt;load]] }<br>
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;referenced HBHA(CO)NH peak list { [[FMCGUI commands#Data.3EHBHACONH.3E|DATA&gt;HBHACONH&gt;load]] }
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;referenced 15N_HSQC peak list { [[FMCGUI commands#Data.3EN15_HSQC.3E|DATA&gt;N15 HSQC&gt;load]] }<br>
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>set tolerances for matching of resonances in different spectral dimensions { [[FMCGUI commands#Data.3ETolerances|Data&gt;Tolerances]] }<br>
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>create bPB-fragments { [[FMCGUI commands#Fragment.3ECreate.3Efawn|Fragment&gt;create&gt;fawn]] }<br>
<div>First, a referenced C13_hsqc peak list is created and shown in new window ‘fake C13 HSQC’. Warning messages are shown in the project main window. You have to check the list and modify it if needed. Then, press ‘OK’ button in the ‘‘fake C13 HSQC’ window. In the result, new window ‘Create Fragment’ pops up. The window consists of three sections. The left sections contains suggested ''b''PB-fragments, while the other sections contains two reports of fragments scoring with&nbsp;both C and H resonances and with only C&nbsp;resonances, respectively. Consider warning messages shown in the project main window and check/modify generated ''b''PB-fragments in the left section of “Create Fragment” window. When satisfied, the ''b''PB-fragments will be loaded in the memory by&nbsp;clicking on “OK” button.</div>
*<span>&nbsp;&nbsp; &nbsp; &nbsp; save project PRJ_1. { [[FMCGUI commands#Project.3ESave|Project&gt;Save]] } or&nbsp; { [[FMCGUI commands#Project.3EQuit|Project&gt;Quit]] } </span>


<div><span>&nbsp;&nbsp;&nbsp;&nbsp; </span></div>
== Step 2. Complete PB-fragments  ==
== Step 2. Complete PB-fragments  ==


==  ==
&nbsp;&nbsp;&nbsp; At this step ''b''PB-fragments are completed with aliphatic side-chain resonances and&nbsp; additional spin-systems (without HN) are identified using the following spectra.  
<div>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; At this step ''b''PB-fragments are completed with aliphatic side-chain resonances and&nbsp; additional spin-systems (without HN) are identified using the following spectra. </div><div>&nbsp;</div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 13C_HSQC</span></div><div>''<span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span>''(H)CCH-TOCSY</div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; H(C)CH-TOCSY</span> </div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 13C_NOESY</span></div><div>&nbsp;</div><div>&nbsp;2.1. Generate expected peak lists for C13HSQC, (H)CCH_TOCSY, and&nbsp;H(C)CH_TOCSY spectra&nbsp;using created ''b''PB-gfragments:</div><div>&nbsp;</div>  
<div>&nbsp;</div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 13C-HSQC</span></div><div>''<span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span>''(H)CCH-TOCSY</div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; H(C)CH-TOCSY</span> </div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 13C-NOESY</span></div><div>&nbsp;</div><div>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 2.1. Generate expected peak lists for C13HSQC, (H)CCH-TOCSY, and&nbsp;H(C)CH-TOCSY spectra&nbsp;using created ''b''PB fragments:</div><div>&nbsp;</div>  
*&nbsp; &nbsp; open project PRJ1 { <span>Project&gt;load }</span>
*&nbsp; &nbsp; open project PRJ1 { [[FMCGUI commands#Project.3ELoad|Project&gt;load]] }  
*&nbsp;&nbsp;&nbsp; generate expected C13hsqc_exp.list that consists of C<sub>a</sub>-H<sub>a</sub> and C<sub>b</sub>-H<sub>b</sub> moieties<span>&nbsp;&nbsp; { Fragment&gt;Expected Peaks&gt;C13HSQC }
*&nbsp;&nbsp;&nbsp; generate expected C13hsqc_exp.list that consists of C<sub>a</sub>-H<sub>a</sub> and C<sub>b</sub>-H<sub>b</sub> moieties<span>&nbsp;&nbsp; { [[FMCGUI commands#Fragment.3EExpected_Peaks.3E|Fragment&gt;Expected Peaks&gt;C13HSQC]] }
 
</span>
</span>


*&nbsp;&nbsp;&nbsp; generate expected CCH-Tocsy.list { [[FMCGUI commands#Fragment.3EExpected_Peaks.3E|Fragment&gt;Expected Peaks&gt;(H)CCH]] }<br>
*&nbsp; &nbsp; generate expected HCH-Tocsy.list { [[FMCGUI commands#Fragment.3EExpected_Peaks.3E|Fragment&gt;Expected Peaks&gt;H(C)CH]]  }<br>
<div>&nbsp;</div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 2.2<span>&nbsp;&nbsp;&nbsp; </span></span>Read the generated peaks into SPARKY.&nbsp;</div><div>&nbsp;</div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; 2.3<span>&nbsp;&nbsp;&nbsp; </span></span>Using SPARKY, complete ''b''PB fragments with aliphatic side-chain resonances by analyzing C<sub>a</sub>-H<sub>a</sub> and C<sub>b</sub>-H<sub>b</sub><span> strips in all CH_rooted spectra (see Figure 4.1B,C). New resonances should be peaked and referenced ''<u>only</u>'' in 13C_HSQC spectrum.</span></div><div>&nbsp;</div>
=== Figure 4.1B,C  ===
<div></div><div></div><div>[[Image:Fmcgui Fig4.1b.jpg|thumb|left|500px]][[Image:Fmcgui Fig4.1c.jpg|thumb|right|500px]]</div><div></div><div></div><div></div><div><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></div><div><br></div><div><span>2.4<span>&nbsp;&nbsp;&nbsp; </span></span>When all peaks corresponding to HN-rooted spin-systems are peaked in 13C_HSQC spectrum, the unpicked peaks are used as a starting point for identification of spin-systems without backbone HN resonances (PB fragments corresponding to residues before prolines in the protein sequence, last residue and residues missing in HN-rooted spectra).</div><div>&nbsp;</div>
<br>
== Step 3. Spin-systems validation and correction  ==
<div>&nbsp;</div><div>Validate PB-fragments using FMCGUI:</div>
*<span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp; start a new project PRJ2 { [[FMCGUI commands#Project.3ENew|Project&gt;new]] } </span>
<br>
<br>


*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load protein sequence { [[FMCGUI commands#Data.3EProtein_Sequence.3ELoad|DATA&gt;Protein Sequence&gt;load]] }
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;referenced 15N_HSQC peak list { [[FMCGUI commands#Data.3EN15_HSQC.3E|DATA&gt;N15 HSQC&gt;load]] }
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;referenced 13C_HSQC peak list { [[FMCGUI commands#Data.3EC13_HSQC.3E|DATA&gt;C13 HSQC&gt;load]] }
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;referenced HNCA peak list { [[FMCGUI commands#Data.3EHNCA.3E|DATA&gt;HNCA&gt;load]] }
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;&nbsp;CBCA(CO)HN peak list { [[FMCGUI commands#Data.3ECBCACONHN.3E|DATA&gt;CBCACOHN&gt;load]] }
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;&nbsp;HNCO peak list { [[FMCGUI commands#Data.3EHNCO.3E|DATA&gt;HNCO&gt;load]] }
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>set tolerances for matching of resonances in different spectral dimensions&nbsp; { [[FMCGUI commands#Data.3ETolerances|DATA&gt;Tolerances]] }
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>create and validate PB fragments { [[FMCGUI commands#Fragment.3ECreate.3Eabacus|Fragment&gt;create&gt;abacus]] }
<div>This command starts script ‘''sps_create’''. In the result, a new window [[FMCGUI commands#Fragment.3ECreate.3Eabacus|"Create Fragment"]] pops up. The warning messages of the ‘''sps_create’'' script are shown in the main window and indicate spin-system that have low score (see [[Introduction to ABACUS#Figure_1.2|Figure 1.2]]), namely, spin-systems with S<sub>max</sub> &lt; 10<sup>-4</sup>. Following the warnings check and modify, if necessary, generated PB fragments in the left section of “Create Fragment’ window. Alternatively, go back to spectra, fix peak lists accordingly, and repeat the fragment generation/validation again.</div><div>When satisfied, the PB fragments will be saved (file "sps_pb.dat" into directory "PRJ2/sps") and loaded in memory by&nbsp;pressing "OK" button in “Create Fragment” window.</div>
*<span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; save project PRJ2 { [[FMCGUI commands#Project.3ESave|Project&gt;Save]] } or { [[FMCGUI commands#Project.3EQuit|Project&gt;Quit]] } </span>


*&nbsp;&nbsp;&nbsp; generate expected CCH_tocsy.list { <span>Fragment&gt;Expected Peaks&gt;(H)CCH</span> }<br>
*&nbsp; &nbsp; generate expected HCH_tocsy.list { <span>Fragment&gt;Expected Peaks&gt;H(C)CH</span> }<br>
<div>&nbsp;</div><div><span>2.2<span>&nbsp;&nbsp;&nbsp; </span></span>Read the generated peaks into SPARKY.&nbsp;</div><div>&nbsp;</div><div><span>2.3<span>&nbsp;&nbsp;&nbsp; </span></span>Using SPARKY, complete ''b''PB-fragments with aliphatic side-chain resonances by analyzing C<sub></sub>-H<sub></sub> <span>&nbsp;and&nbsp;C<sub></sub>-H<sub></sub> strips in all CH_rooted spectra (see Figure 4.1B,C). New resonances should be peaked and referenced ''<u>only</u>'' in 13C_HSQC spectrum.</span></div><div>&nbsp;</div><div><span>2.4<span>&nbsp;&nbsp;&nbsp; </span></span>When all peaks corresponding to HN-rooted spin-systems are peaked in 13C_HSQC spectrum, the unpicked peaks are used as a starting point for identification of spin-systems without backbone HN resonances (PB-fragments corresponding to residues before prolines in the protein sequence, last residue and residues missing in HN-rooted spectra).</div><div>&nbsp;</div>
<br>


== Step 3. Spin-systems validation and correction ==
<div>'''&nbsp;'''</div>
<div>&nbsp;</div><div>Validate PB-fragments using FMCGUI:</div>
*<span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp; start a new project PRJ2 [Project&gt;new]</span>
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load protein sequence [<span>DATA&gt;Protein Sequence&gt;load</span>]
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;referenced 15N_HSQC peak list [<span>DATA&gt;N15 HSQC&gt;load</span>]
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;referenced 13C_HSQC peak list [<span>DATA&gt;C13 HSQC&gt;load</span>]
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;referenced HNCA peak list [<span>DATA&gt;HNCA&gt;load</span>]
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;&nbsp;CBCA(CO)HN peak list [<span>DATA&gt;CBCACOHN&gt;load</span>]
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>load&nbsp;&nbsp;HNCO peak list [<span>DATA&gt;HNCO&gt;load</span>]
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>set tolerances for matching of resonances in different spectral dimensions&nbsp;[<span>DATA&gt;Tolerances</span>]
*<span><span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; </span></span>create PB-fragments [<span>Fragment&gt;create&gt;abacus</span>]
<div>This command starts script ‘''sps_create’''. In the result, a new window ‘Create Fragment’ pops up. The warning messages of the ‘''sps_create’'' script are shown in the main window and indicate spin-system that have low score, namely, S<sub>max</sub> &lt; 10<sup>-4</sup>. Following the warnings check and modify, if necessary, generated PB-fragments in the left section of “Create Fragment’ window (see Figure 2.5). Alternatively, go back to spectra, fix peak lists accordingly, and repeat the fragment generation/validation again.</div><div>When satisfied, the PB-fragments will be saved (file ‘sps_pb.dat’ into directory PRJ2/sps) and loaded in the memory by&nbsp;pressing OK button in “Create Fragment” window.</div>
*<span>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; save project PRJ2 [Project&gt;Save] or [Project&gt;Quit]</span>
<div>'''&nbsp;'''</div>  
<br>
<br>

Latest revision as of 21:18, 6 January 2010

Normally, the NMR spectra shown in Table 1 are collected for ABCUS. Spectra should ideally be collected from the same protein preparation and under the same conditions to make sure peaks are within tolerance between spectra. All spectra need to be appropriately synchronized and calibrated against reference spectra of your choice. It is a good idea to use as a reference for spectra calibration the 2D HN-projection of 15N-NOESY and the 2D CH-projection of the 13C-NOESY.
 

Step 1. Generate HN-rooted spin-systems (bPB-fragments)

1.1bPB-fragments can be identified using the following spectra


             15N_HSQC
             HNCO
             CBCA(CO)NH
             HBHAC (CO)NH
             HNCA
            15N_NOESY
 It is a good idea to analyze all these spectra simultaneously, for example,  using SPARKY, in order to obtain  peak lists of 15N_HSQC, HNCA,  CBCA(CO)NH, and HBHA(CO)NH spectra (see Figure 4.1A). The first two spectra should be referenced.
 
 Figure 4.1A
Fmcgui Fig4.1a.jpg
 
        1.2. Create initial HN-rooted spin-systems (bPB-fragments ) using FMCGUI:
 
First, a referenced C13_hsqc peak list is created and shown in new window ‘fake C13 HSQC’. Warning messages are shown in the project main window. You have to check the list and modify it if needed. Then, press ‘OK’ button in the ‘‘fake C13 HSQC’ window. In the result, new window ‘Create Fragment’ pops up. The window consists of three sections. The left sections contains suggested bPB-fragments, while the other sections contains two reports of fragments scoring with both C and H resonances and with only C resonances, respectively. Consider warning messages shown in the project main window and check/modify generated bPB-fragments in the left section of “Create Fragment” window. When satisfied, the bPB-fragments will be loaded in the memory by clicking on “OK” button.

Step 2. Complete PB-fragments

    At this step bPB-fragments are completed with aliphatic side-chain resonances and  additional spin-systems (without HN) are identified using the following spectra.

 
               13C-HSQC
               (H)CCH-TOCSY
               H(C)CH-TOCSY
               13C-NOESY
 
        2.1. Generate expected peak lists for C13HSQC, (H)CCH-TOCSY, and H(C)CH-TOCSY spectra using created bPB fragments:
 

 
        2.2    Read the generated peaks into SPARKY. 
 
        2.3    Using SPARKY, complete bPB fragments with aliphatic side-chain resonances by analyzing Ca-Ha and Cb-Hb strips in all CH_rooted spectra (see Figure 4.1B,C). New resonances should be peaked and referenced only in 13C_HSQC spectrum.
 

Figure 4.1B,C

Fmcgui Fig4.1b.jpg
Fmcgui Fig4.1c.jpg
       

2.4    When all peaks corresponding to HN-rooted spin-systems are peaked in 13C_HSQC spectrum, the unpicked peaks are used as a starting point for identification of spin-systems without backbone HN resonances (PB fragments corresponding to residues before prolines in the protein sequence, last residue and residues missing in HN-rooted spectra).
 


Step 3. Spin-systems validation and correction

 
Validate PB-fragments using FMCGUI:
  •         start a new project PRJ2 { Project>new }




This command starts script ‘sps_create’. In the result, a new window "Create Fragment" pops up. The warning messages of the ‘sps_create’ script are shown in the main window and indicate spin-system that have low score (see Figure 1.2), namely, spin-systems with Smax < 10-4. Following the warnings check and modify, if necessary, generated PB fragments in the left section of “Create Fragment’ window. Alternatively, go back to spectra, fix peak lists accordingly, and repeat the fragment generation/validation again.
When satisfied, the PB fragments will be saved (file "sps_pb.dat" into directory "PRJ2/sps") and loaded in memory by pressing "OK" button in “Create Fragment” window.